My Binding Standard APC45 Programmable Manual de Instruções Página 1

Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com Standard APC45 Programmable Paper Cutter

21-2 Control Panel DescriptionsCEnt=====M1M2M3Control PanelBackgauge BackwardBackgauge ForwardWhen pressing once, movesby 0.1 mm (0.005”)When continu

3Cutting MechanismMachine Descriptions1-3 Cutting Mechanism124576MM312376845Knife HolderKnifeAfter the clamp presses thesheets, this knife holder low

4This page is intentionally left blank.

5Check the Power Switch Safety Checks2-1 Check the Power SwitchThis machine has been designed to be assafe as possible. However, if an accidentoccurs

62-1 Check the Power SwitchCheck the current position of the backgauge.- If the value “400.0” appears in the currentposition box and guide window, th

7Check the Cutting Buttons Safety Checks2-2 Check the Cutting ButtonsIn the following steps, if the machine does not operate as explained “the machin

82-3 Check the Beam Light SensorsTurn on the power switch.- When the initialization is completed, the cur-rent position value (=400.0) appears.Check

9Check the Control Panel Safety Checks2-4 Check the Control PanelPress the button.- Press the button once and release.- If the value of the current

102-5 Check the Foot PedalIn the following steps, if the machine does not operate as explained “the machine is OK”, stop the check immediately.The fo

11Cutting Operation on the Cutting Line Operation Procedures 3-1 Cutting Operation on the Cutting LinePress the button.- The LED on the upper left

123-1 Cutting Operation on the Cutting LineAlign the desired cutting position with the cutting line.- Align the desired cutting position with the cut

13Cutting Operation on the Cutting Line Operation Procedures3-1 Cutting Operation on the Cutting LineRemove the cut sheets.- The value of the cutting

143-2 Cutting Operation by Entering a ValueThis section explains the cutting operationwhen entering a value directly withoutusing program.Press the

15Cutting Operation by Entering a Value Operation Procedures3-2 Cutting Operation by Entering a ValueSet the automatic push-out mode.- When the autom

163-2 Cutting Operation by Entering a ValueEnter the value of the cutting length for the next cutting.- Repeat from the step .- If the cutting opera

17Cutting Operation by Programmed Value Operation Procedures3-3 Cutting Operation by Programmed ValueThis section explains the cutting operationperfo

183-3 Cutting Operation by Programmed ValuePlace the sheets.- The maximum cutting height is 60 mm (2.36”).- Arrange the sheets by aligning them with

19Cutting Operation by Programmed Value Operation Procedures3-3 Cutting Operation by Programmed ValueRepeat the cutting operation in the same way.- W

203-4 Function CuttingThis section explains how to recall the cut-ting job performed most frequently usingthe function keys M1 through M3.Three progr

21Function Cutting Operation Procedures3-4 Function CuttingPerform the cutting operation of the step 1.- Press both cutting buttons.- When the step 1

I• This manual is designed to help you to install, operate and maintain the APC-45 Paper Cutter. Please read and understand this manual, and keep it i

223-5 Compression OperationThis section explains how to reduce thebulk of the saddle-stitched booklets usingthe pressure of the clamp.Press the but

23Creating a Cutting Program (Input) Operation Procedures3-6 Creating a Cutting Program (Input)When repeating a complicated cutting job,it is helpful

243-6 Creating a Cutting Program (Input)Input the cutting length for the step 1.- In this step, the cutting length of the step 1 should be 320.0 for

25Creating a Cutting Program (Input) Operation Procedures3-6 Creating a Cutting Program (Input)Input the cutting length for the last step.- Press the

263-6 Creating a Cutting Program (Correct)This section explains how to correct thesaved program.Example: When enlarging the cuttinglength by 0.5 mm a

27Creating a Cutting Program (Correct) Operation Procedures3-6 Creating a Cutting Program (Correct)Show the step 3 to correct.- Press the key for t

283-6 Creating a Cutting Program (Delete)This section explains how to delete thesaved program.Example: When deleting course number 5.[Deleting the Sa

29Creating a Cutting Program (Correct) Operation Procedures3-6 Creating a Cutting Program (Repeat Cutting Program)When using the button, the progra

303-6 Creating a Cutting Program (Repeat Cutting Program)Input “0” to the step 3.- When the keys are input to the cut-ting length, the confirmation

31Checking the Counter Operation Procedures3-7 Checking the CounterThis section explains how to indicate thefrequency of the total cut since themachi

IIHorizon International Inc. cannot anticipate every possible situation that might involve a potential hazard. The instructions in this manual and war

323-8 Knife Replacement MessageWhen the cutting operation has been doneover 1,000 times since the last knifereplacement, the message shown at lowerri

33Knife Lower Limit Adjustment Replacement and Adjustment 4-1 Knife Lower Limit AdjustmentThe lowest position of the knife can beadjusted mechanicall

344-1 Knife Lower Limit AdjustmentAdjust the lower limit.- Insert the accessory driver into the adjusting hole and rotate the shaft to adjust the low

35Knife Angle Adjustment Replacement and Adjustment4-2 Knife Angle AdjustmentAdjust the knife angle if part of the sheetsremain uncut as shown in the

364-2 Knife Angle AdjustmentTurn on the power switch.- The indication [LOWER KNIFE] is shown on the guide window.Press the cutting buttons and keep p

37Knife Angle Adjustment Replacement and Adjustment4-2 Knife Angle AdjustmentFasten the lock screw.Close the window for adjustment.- Fasten the mount

38Cutting Stick Replacement Replacement and Adjustment4-3 Cutting Stick ReplacementWhen the groove of the cutting stickbecomes deep, the bottom sheet

39An Error Message Appears Troubleshooting5-1 An Error Message Appears5. TroubleshootingError Message Cause RemedyE01: KNIFE HOME ERRORThe knife is n

405-2 Problems and Remedies5-2-1 Stain, Diagonal Line, Pressing Mark and Uncut of the SheetsProblem Causes and Remedies SeeSheets are cut diago-nally

41Problems and Remedies Troubleshooting5-2 Problems And RemediesProblem Causes and Remedies SeeSheet remains uncut.• If the cutting stick is worn, th

IIISafety Operation Precautions WARNING for OperationThis machine must be operated by just one person at a time.Va

42This page is intentionally left blank.

Lubrication (Front Side)43Maintenance6-1 Lubrication (Front Side)Turn on the power switch.Stop the knife at the bottom.- Press the cutting buttons an

446-1 Lubrication (Rear Side)Turn on the power switch.Move the backgauge backward.- Move the backgauge to the far end.Lubricate each section.- There

45Specifications Appendix7-1 SpecificationsCutting Width Max. 450 mm (17.71")Cutting Height Max. 60 mm (2.36")Feed Depth Max. 450 mm (17.71

467-2 AccessoriesToo l B o x (4003344) 1 pcWooden Box(M007425) 1 pcBox Wrench (4004368)

IVSpace Required for InstallationAs the electrical parts are installed on the lower left of the machine, repair work may be done from theright side. A

VCONTENTSImportant Information... ISafety Precautions...

VIThis page is intentionally left blank.

1Machine DescriptionsMachine Descriptions1-1 Machine Descriptions1. Machine DescriptionsThis chapter explains the positions and functions of each par